U-Boot SPL 2021.10 (Feb 12 2023 - 18:15:33 +0800) DDR version: dc2e84f0. Trying to boot from SPI OpenSBI v1.2 ____ _____ ____ _____ / __ \ / ____| _ \_ _| | | | |_ __ ___ _ __ | (___ | |_) || | | | | | '_ \ / _ \ '_ \ \___ \| _ < | | | |__| | |_) | __/ | | |____) | |_) || |_ \____/| .__/ \___|_| |_|_____/|____/_____| | | |_| Platform Name : StarFive VisionFive V2 Platform Features : medeleg Platform HART Count : 5 Platform IPI Device : aclint-mswi Platform Timer Device : aclint-mtimer @ 4000000Hz Platform Console Device : uart8250 Platform HSM Device : jh7110-hsm Platform PMU Device : --- Platform Reboot Device : pm-reset Platform Shutdown Device : pm-reset Firmware Base : 0x40000000 Firmware Size : 292 KB Runtime SBI Version : 1.0 Domain0 Name : root Domain0 Boot HART : 1 Domain0 HARTs : 0*,1*,2*,3*,4* Domain0 Region00 : 0x0000000002000000-0x000000000200ffff (I) Domain0 Region01 : 0x0000000040000000-0x000000004007ffff () Domain0 Region02 : 0x0000000000000000-0xffffffffffffffff (R,W,X) Domain0 Next Address : 0x0000000040200000 Domain0 Next Arg1 : 0x0000000042200000 Domain0 Next Mode : S-mode Domain0 SysReset : yes Boot HART ID : 1 Boot HART Domain : root Boot HART Priv Version : v1.11 Boot HART Base ISA : rv64imafdcbx Boot HART ISA Extensions : none Boot HART PMP Count : 8 Boot HART PMP Granularity : 4096 Boot HART PMP Address Bits: 34 Boot HART MHPM Count : 2 Boot HART MIDELEG : 0x0000000000000222 Boot HART MEDELEG : 0x000000000000b109 U-Boot 2021.10 (Feb 12 2023 - 18:15:33 +0800), Build: jenkins-VF2_515_Branch_SDK_Release-24 CPU: rv64imacu Model: StarFive VisionFive V2 DRAM: 8 GiB MMC: sdio0@16010000: 0, sdio1@16020000: 1 Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB *** Warning - bad CRC, using default environment StarFive EEPROM format v2 --------EEPROM INFO-------- Vendor : StarFive Technology Co., Ltd. Product full SN: [REDACTED] data version: 0x2 PCB revision: 0xb2 BOM revision: A Ethernet MAC0 address: [REDACTED] Ethernet MAC1 address: [REDACTED] --------EEPROM INFO-------- In: serial@10000000 Out: serial@10000000 Err: serial@10000000 Model: StarFive VisionFive V2 Net: eth0: ethernet@16030000, eth1: ethernet@16040000 switch to partitions #0, OK mmc1 is current device found device 1 bootmode flash device 1 Failed to load 'uEnv.txt' Can't set block device Hit any key to stop autoboot: 0 1579 bytes read in 6 ms (256.8 KiB/s) Importing environment from mmc1 ... Can't set block device ## Warning: defaulting to text format switch to partitions #0, OK mmc1 is current device 133575318 bytes read in 5582 ms (22.8 MiB/s) ## Loading kernel from FIT Image at a0000000 ... Using 'config-1' configuration Trying 'vmlinux' kernel subimage Description: vmlinux Type: Kernel Image Compression: uncompressed Data Start: 0xa00000c8 Data Size: 24161280 Bytes = 23 MiB Architecture: RISC-V OS: Linux Load Address: 0x40200000 Entry Point: 0x40200000 Verifying Hash Integrity ... OK ## Loading fdt from FIT Image at a0000000 ... Using 'config-1' configuration Trying 'fdt' fdt subimage Description: unavailable Type: Flat Device Tree Compression: uncompressed Data Start: 0xa7f57054 Data Size: 48366 Bytes = 47.2 KiB Architecture: RISC-V Load Address: 0x46000000 Hash algo: sha256 Hash value: dae1bdb73c5a4806cc8ff17df2552c3152c5d858e76f89212a3de4714e63e40b Verifying Hash Integrity ... sha256+ OK Loading fdt from 0xa7f57054 to 0x46000000 Booting using the fdt blob at 0x46000000 ## Loading loadables from FIT Image at a0000000 ... Trying 'ramdisk' loadables subimage Description: buildroot initramfs Type: RAMDisk Image Compression: uncompressed Data Start: 0xa170ad7c Data Size: 109363724 Bytes = 104.3 MiB Architecture: RISC-V OS: Linux Load Address: 0x46100000 Entry Point: unavailable Hash algo: sha256 Hash value: 9d8021a473fe51890abfc8f6941b85d15ce2eac415beb56bba9da4fbb7191233 Verifying Hash Integrity ... sha256+ OK Loading loadables from 0xa170ad7c to 0x46100000 Loading Kernel Image ## Error: "cpu_vol_set" not defined Booting kernel in ## Flattened Device Tree blob at 46000000 Booting using the fdt blob at 0x46000000 Using Device Tree in place at 0000000046000000, end 000000004600efff Starting kernel ... clk u5_dw_i2c_clk_core already disabled clk u5_dw_i2c_clk_apb already disabled [ 0.000000] Linux version 5.15.0 (jenkins@soft05) (riscv64-buildroot-linux-gnu-gcc.br_real (Buildroot VF2_v2.11.5) 13 [ 0.000000] OF: fdt: Ignoring memory range 0x40000000 - 0x40200000 [ 0.000000] Machine model: StarFive VisionFive V2 [ 0.000000] earlycon: sbi0 at I/O port 0x0 (options '') [ 0.000000] printk: bootconsole [sbi0] enabled [ 0.000000] efi: UEFI not found. [ 0.000000] Reserved memory: created CMA memory pool at 0x0000000080000000, size 512 MiB [ 0.000000] OF: reserved mem: initialized node linux,cma, compatible id shared-dma-pool [ 0.000000] Zone ranges: [ 0.000000] DMA32 [mem 0x0000000040200000-0x00000000ffffffff] [ 0.000000] Normal [mem 0x0000000100000000-0x000000023fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040200000-0x00000000c010ffff] [ 0.000000] node 0: [mem 0x00000000c0110000-0x00000000c01fffff] [ 0.000000] node 0: [mem 0x00000000c0200000-0x000000023fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040200000-0x000000023fffffff] [ 0.000000] SBI specification v1.0 detected [ 0.000000] SBI implementation ID=0x1 Version=0x10002 [ 0.000000] SBI TIME extension detected [ 0.000000] SBI IPI extension detected [ 0.000000] SBI RFENCE extension detected [ 0.000000] SBI SRST extension detected [ 0.000000] SBI v0.2 HSM extension detected [ 0.000000] CPU with hartid=0 is not available [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv: base ISA extensions acdfim [ 0.000000] riscv: ELF capabilities acdfim [ 0.000000] percpu: Embedded 18 pages/cpu s33960 r8192 d31576 u73728 [ 0.000000] pcpu-alloc: s33960 r8192 d31576 u73728 alloc=18*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 2067975 [ 0.000000] Kernel command line: earlyprintk console=tty1 console=ttyS0,115200 debug rootwait earlycon=sbi root=/dev4 [ 0.000000] Unknown command line parameters: earlyprintk [ 0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear) [ 0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: mapped [mem 0x00000000fbfff000-0x00000000fffff000] (64MB) [ 0.000000] Memory: 7459112K/8386560K available (10389K kernel code, 5013K rwdata, 4096K rodata, 2197K init, 412K bs) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4. [ 0.000000] rcu: RCU debug extended QS entry/exit. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] CPU with hartid=0 is not available [ 0.000000] riscv-intc: unable to find hart id for /cpus/cpu@0/interrupt-controller [ 0.000000] riscv-intc: 64 local interrupts mapped [ 0.000000] plic: plic@c000000: mapped 136 interrupts with 4 handlers for 9 contexts. [ 0.000000] random: get_random_bytes called from start_kernel+0x4d0/0x6ea with crng_init=0 [ 0.000000] riscv_timer_init_dt: Registering clocksource cpuid [0] hartid [1] [ 0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404s [ 0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns [ 0.008242] clocksource: timer@13050000.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.018465] clocksource: timer@13050000.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.028779] clocksource: timer@13050000.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.039094] clocksource: timer@13050000.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns [ 0.049608] Console: colour dummy device 80x25 [ 0.055347] printk: console [tty1] enabled [ 0.059410] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=40000) [ 0.069615] pid_max: default: 32768 minimum: 301 [ 0.074551] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.082237] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.091644] ASID allocator disabled [ 0.095177] rcu: Hierarchical SRCU implementation. [ 0.100098] EFI services will not be available. [ 0.104950] smp: Bringing up secondary CPUs ... [ 0.111059] smp: Brought up 1 node, 4 CPUs [ 0.117105] devtmpfs: initialized [ 0.128145] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.137953] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.158489] pinctrl core: initialized pinctrl subsystem [ 0.164544] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.171093] thermal_sys: Registered thermal governor 'step_wise' [ 0.171427] cpuidle: using governor menu [ 0.203336] platform soc:dsi-output: Fixing up cyclic dependency with 29400000.dc8200 [ 0.211664] platform 295d0000.mipi: Fixing up cyclic dependency with soc:dsi-output [ 0.219676] platform 29590000.hdmi: Fixing up cyclic dependency with 29400000.dc8200 [ 0.239769] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.246408] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.256484] vgaarb: loaded [ 0.259359] SCSI subsystem initialized [ 0.263207] libata version 3.00 loaded. [ 0.267144] usbcore: registered new interface driver usbfs [ 0.272596] usbcore: registered new interface driver hub [ 0.277978] usbcore: registered new device driver usb [ 0.283331] mc: Linux media interface: v0.10 [ 0.287551] videodev: Linux video capture interface: v2.00 [ 0.293289] Advanced Linux Sound Architecture Driver Initialized. [ 0.299687] Bluetooth: Core ver 2.22 [ 0.303230] NET: Registered PF_BLUETOOTH protocol family [ 0.308565] Bluetooth: HCI device and connection manager initialized [ 0.314994] Bluetooth: HCI socket layer initialized [ 0.319924] Bluetooth: L2CAP socket layer initialized [ 0.325059] Bluetooth: SCO socket layer initialized [ 0.330273] clocksource: Switched to clocksource riscv_clocksource [ 0.343905] NET: Registered PF_INET protocol family [ 0.349665] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear) [ 0.364925] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 163840 bytes, linear) [ 0.373739] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.382443] TCP bind hash table entries: 65536 (order: 9, 2097152 bytes, linear) [ 0.392391] TCP: Hash tables configured (established 65536 bind 65536) [ 0.399157] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 0.406384] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear) [ 0.414133] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.420430] RPC: Registered named UNIX socket transport module. [ 0.426291] RPC: Registered udp transport module. [ 0.431070] RPC: Registered tcp transport module. [ 0.435820] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.443065] PCI: CLS 0 bytes, default 64 [ 0.447480] Unpacking initramfs... [ 0.447917] Initialise system trusted keyrings [ 0.455506] workingset: timestamp_bits=62 max_order=21 bucket_order=0 [ 0.468114] NFS: Registering the id_resolver key type [ 0.473160] Key type id_resolver registered [ 0.477351] Key type id_legacy registered [ 0.481535] nfs4filelayout_init: NFSv4 File Layout Driver Registering... [ 0.488187] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering... [ 0.495707] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.500355] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. [ 0.506998] fuse: init (API version 7.34) [ 0.550949] NET: Registered PF_ALG protocol family [ 0.555704] Key type asymmetric registered [ 0.559849] Asymmetric key parser 'x509' registered [ 0.564932] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 249) [ 0.572301] io scheduler mq-deadline registered [ 0.576858] io scheduler kyber registered [ 0.581408] start plist test [ 0.587834] end plist test [ 0.691212] clk-starfive-jh7110 13020000.clock-controller: starfive JH7110 clkgen init successfully. [ 0.701532] L2CACHE: DataError @ 0x00000000.08040140 [ 0.706500] L2CACHE: DataFail @ 0x00000000.0804005B [ 0.711479] L2CACHE: No. of Banks in the cache: 8 [ 0.716149] L2CACHE: No. of ways per bank: 16 [ 0.720587] L2CACHE: Sets per bank: 256 [ 0.724467] L2CACHE: Bytes per cache block: 64 [ 0.728975] L2CACHE: Index of the largest way enabled: 15 [ 0.734798] jh7110-pmu 17030000.power-controller: registered 8 power domains [ 0.805689] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled [ 0.815638] @@#########################@@ [ 0.825697] @@ dev ptr:ffffffe0bfefe800/1500/1 [ 0.830392] PVR_K: 1: Read BVNC 36.50.54.182 from HW device registers [ 0.836934] PVR_K: 1: RGX Device registered BVNC 36.50.54.182 with 1 core in the system [ 6.692807] Initramfs unpacking failed: invalid magic at start of compressed archive [ 6.888176] Freeing initrd memory: 130444K [ 6.893053] PVR_K: 1: RGX Firmware image 'rgx.fw.36.50.54.182' loaded [ 6.903269] PVR_K: 1: Shader binary image 'rgx.sh.36.50.54.182' loaded [ 6.912145] [drm] Initialized pvr 1.17.6210866 20170530 for 18000000.gpu on minor 0 [ 6.928804] loop: module loaded [ 6.934329] spi-nor spi0.0: gd25lq128d (16384 Kbytes) [ 6.950658] 3 fixed-partitions partitions found on MTD device 13010000.spi.0 [ 6.957668] Creating 3 MTD partitions on "13010000.spi.0": [ 6.963235] 0x000000000000-0x000000040000 : "spl" [ 6.969786] 0x000000100000-0x000000400000 : "uboot" [ 6.976210] 0x000000f00000-0x000001000000 : "data" [ 6.983656] libphy: Fixed MDIO Bus: probed [ 6.989167] CAN device driver interface [ 6.993566] starfive-eth-plat 16030000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set. [ 7.003885] starfive-eth-plat 16030000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 7.011339] starfive-eth-plat 16030000.ethernet: DWMAC4/5 [ 7.016853] starfive-eth-plat 16030000.ethernet: DMA HW capability register supported [ 7.024759] starfive-eth-plat 16030000.ethernet: RX Checksum Offload Engine supported [ 7.032645] starfive-eth-plat 16030000.ethernet: Wake-Up On Lan supported [ 7.039537] starfive-eth-plat 16030000.ethernet: TSO supported [ 7.045378] starfive-eth-plat 16030000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 7.053794] starfive-eth-plat 16030000.ethernet: Enabled Flow TC (entries=1) [ 7.060892] starfive-eth-plat 16030000.ethernet: TSO feature enabled [ 7.067293] starfive-eth-plat 16030000.ethernet: Using 40 bits DMA width [ 7.316990] libphy: stmmac: probed [ 7.320378] YT8531 Gigabit Ethernet stmmac-0:00: attached PHY driver (mii_bus:phy_addr=stmmac-0:00, irq=POLL) [ 7.330332] YT8531 Gigabit Ethernet stmmac-0:01: attached PHY driver (mii_bus:phy_addr=stmmac-0:01, irq=POLL) [ 7.341497] starfive-eth-plat 16040000.ethernet: force_sf_dma_mode is ignored if force_thresh_dma_mode is set. [ 7.351837] starfive-eth-plat 16040000.ethernet: User ID: 0x41, Synopsys ID: 0x52 [ 7.359270] starfive-eth-plat 16040000.ethernet: DWMAC4/5 [ 7.364826] starfive-eth-plat 16040000.ethernet: DMA HW capability register supported [ 7.372713] starfive-eth-plat 16040000.ethernet: RX Checksum Offload Engine supported [ 7.380598] starfive-eth-plat 16040000.ethernet: Wake-Up On Lan supported [ 7.387494] starfive-eth-plat 16040000.ethernet: TSO supported [ 7.393334] starfive-eth-plat 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 7.401752] starfive-eth-plat 16040000.ethernet: Enabled Flow TC (entries=1) [ 7.408831] starfive-eth-plat 16040000.ethernet: TSO feature enabled [ 7.415258] starfive-eth-plat 16040000.ethernet: Using 40 bits DMA width [ 7.664077] libphy: stmmac: probed [ 7.667432] YT8531 Gigabit Ethernet stmmac-1:00: attached PHY driver (mii_bus:phy_addr=stmmac-1:00, irq=POLL) [ 7.677433] YT8531 Gigabit Ethernet stmmac-1:01: attached PHY driver (mii_bus:phy_addr=stmmac-1:01, irq=POLL) [ 7.688895] Intel(R) Wireless WiFi driver for Linux [ 7.695813] cdns3-starfive 10210000.usbdrd: usb mode 2 2.0 probe success [ 7.703249] usbcore: registered new interface driver uas [ 7.708553] usbcore: registered new interface driver usb-storage [ 7.730746] starfive-rtc 17040000.rtc: registered as rtc0 [ 7.736097] starfive-rtc 17040000.rtc: setting system clock to 2001-01-01T00:00:00 UTC (978307200) [ 7.745261] i2c_dev: i2c /dev entries driver [ 7.749717] usbcore: registered new interface driver uvcvideo [ 7.770305] thermal thermal_zone0: failed to read out thermal zone (-110) [ 7.777352] starfive-wdt 13070000.wdog: Heartbeat: timeout=15, count/2=180000000 (0aba9500) [ 7.786210] Bluetooth: HCI UART driver ver 2.3 [ 7.790619] Bluetooth: HCI UART protocol H4 registered [ 7.796474] sdhci: Secure Digital Host Controller Interface driver [ 7.802633] sdhci: Copyright(c) Pierre Ossman [ 7.807056] Synopsys Designware Multimedia Card Interface Driver [ 7.813422] sdhci-pltfm: SDHCI platform and OF driver helper [ 7.819847] jh7110-sec 16000000.crypto: Unable to request sec_m dma channel in DMA channel [ 7.828094] jh7110-sec 16000000.crypto: Cannot initial dma chan [ 7.834350] usbcore: registered new interface driver usbhid [ 7.839870] usbhid: USB HID core driver [ 7.843969] riscv-pmu-sbi: SBI PMU extension is available [ 7.849328] riscv-pmu-sbi: 16 firmware and 4 hardware counters [ 7.855212] riscv-pmu-sbi: Perf sampling/filtering is not supported as sscof extension is not available [ 7.865019] usbcore: registered new interface driver snd-usb-audio [ 7.880489] NET: Registered PF_INET6 protocol family [ 7.886785] Segment Routing with IPv6 [ 7.890450] In-situ OAM (IOAM) with IPv6 [ 7.894486] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver [ 7.900982] NET: Registered PF_PACKET protocol family [ 7.905983] can: controller area network core [ 7.910510] NET: Registered PF_CAN protocol family [ 7.915248] can: raw protocol [ 7.918281] can: broadcast manager protocol [ 7.922550] can: netlink gateway - max_hops=1 [ 7.927206] Bluetooth: RFCOMM TTY layer initialized [ 7.932062] Bluetooth: RFCOMM socket layer initialized [ 7.937250] Bluetooth: RFCOMM ver 1.11 [ 7.941090] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 7.946416] Bluetooth: BNEP filters: protocol multicast [ 7.951720] Bluetooth: BNEP socket layer initialized [ 7.956787] lib80211: common routines for IEEE802.11 drivers [ 7.962467] lib80211_crypt: registered algorithm 'NULL' [ 7.967736] lib80211_crypt: registered algorithm 'WEP' [ 7.972947] lib80211_crypt: registered algorithm 'CCMP' [ 7.978222] lib80211_crypt: registered algorithm 'TKIP' [ 7.983642] 9pnet: Installing 9P2000 support [ 7.987905] Key type dns_resolver registered [ 7.992972] Loading compiled-in X.509 certificates [ 8.036032] starfive_jh7110-pinctrl 13040000.gpio: SiFive GPIO chip registered 64 GPIOs [ 8.044777] starfive_jh7110-pinctrl 17020000.gpio: SiFive GPIO chip registered 4 GPIOs [ 8.052898] pl08xdmac 16008000.sec_dma: initialized 8 virtual memcpy channels [ 8.059993] pl08xdmac 16008000.sec_dma: initialized 16 virtual slave channels [ 8.068950] debugfs: Directory '16008000.sec_dma' with parent 'dmaengine' already present! [ 8.077225] pl08xdmac 16008000.sec_dma: DMA: PL080 rev0 at 0x16008000 irq 23 [ 8.084558] ssp-pl022 10060000.spi: ARM PL022 driver for StarFive SoC platform, device ID: 0x00041022 [ 8.093783] ssp-pl022 10060000.spi: mapped registers from 0x0000000010060000 to (____ptrval____) [ 8.103032] ssp-pl022 10060000.spi: Requested frequency: 10000000 Hz is unsupported,select by default 8250000 Hz [ 8.113569] ssp-pl022 10060000.spi: will use autosuspend for runtime pm, delay 100ms [ 8.122661] i2c 2-0045: Fixing up cyclic dependency with 295d0000.mipi [ 8.129411] seeed_panel 2-0045: Unknown Atmel firmware revision: 0x00 [ 8.136024] tinker_ft5406 2-0038: Address = 0x38 [ 8.140591] tinker_ft5406 2-0038: width = 800, height = 480, reverse = 1 [ 8.147470] tinker_ft5406 2-0038: i2c read error, -121 [ 8.152575] tinker_ft5406 2-0038: Checking touch ic failed [ 8.158095] tinker_ft5406: probe of 2-0038 failed with error -121 [ 8.164459] i2c 2-0019: Fixing up cyclic dependency with 295d0000.mipi [ 8.171886] Goodix-TS 2-0014: supply AVDD28 not found, using dummy regulator [ 8.179007] Goodix-TS 2-0014: supply VDDIO not found, using dummy regulator [ 8.300434] Goodix-TS 2-0014: i2c test failed attempt 1: -121 [ 8.340432] Goodix-TS 2-0014: i2c test failed attempt 2: -121 [ 8.380297] Goodix-TS 2-0014: I2C communication failure: -121 [ 8.386154] Goodix-TS: probe of 2-0014 failed with error -121 [ 8.392870] at24 5-0050: supply vcc not found, using dummy regulator [ 8.399994] at24 5-0050: 512 byte 24c04 EEPROM, writable, 16 bytes/write [ 8.408609] axp15060-regulator 5-0036: Register mipi_0p9 done! vol range:900 ~ 900 mV [ 8.417938] axp15060-regulator 5-0036: Register hdmi_1p8 done! vol range:1800 ~ 1800 mV [ 8.427412] axp15060-regulator 5-0036: Register hdmi_0p9 done! vol range:900 ~ 900 mV [ 8.436727] axp15060-regulator 5-0036: Register cpu_vdd done! vol range:500 ~ 1540 mV [ 8.445332] i2c 6-0010: Fixing up cyclic dependency with 19800000.vin_sysctl [ 8.452760] imx219 6-0010: supply VANA not found, using dummy regulator [ 8.459442] imx219 6-0010: supply VDIG not found, using dummy regulator [ 8.466103] imx219 6-0010: supply VDDL not found, using dummy regulator [ 8.480158] imx219 6-0010: failed to read chip id 219 [ 8.485373] imx219: probe of 6-0010 failed with error -5 [ 8.493353] pcie_plda 2b000000.pcie: host bridge /soc/pcie@2B000000 ranges: [ 8.500345] pcie_plda 2b000000.pcie: MEM 0x0030000000..0x0037ffffff -> 0x0030000000 [ 8.508443] pcie_plda 2b000000.pcie: MEM 0x0900000000..0x093fffffff -> 0x0900000000 [ 8.516637] ATR entry: 0x0940000000 -> 0x0000000000 [0x0010000000] (param: 0x000001) [ 8.524396] ATR entry: 0x0030000000 -> 0x0030000000 [0x0008000000] (param: 0x000000) [ 8.532189] ATR entry: 0x0900000000 -> 0x0900000000 [0x0040000000] (param: 0x000000) [ 8.880375] pcie_plda 2b000000.pcie: Port link up. [ 8.885301] pcie_plda 2b000000.pcie: PCI host bridge to bus 0000:00 [ 8.891535] pci_bus 0000:00: root bus resource [bus 00-ff] [ 8.897057] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 8.904009] pci_bus 0000:00: root bus resource [mem 0x900000000-0x93fffffff pref] [ 8.911581] pci 0000:00:00.0: [1556:1111] type 01 class 0x060400 [ 8.917608] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0xffffffff 64bit pref] [ 8.924956] pci 0000:00:00.0: supports D1 D2 [ 8.929209] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 8.939441] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 8.947555] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330 [ 8.953531] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit] [ 8.960448] pci 0000:01:00.0: PME# supported from D0 D3cold [ 8.969340] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 8.975950] pci 0000:00:00.0: BAR 0: no space for [mem size 0x100000000 64bit pref] [ 8.983638] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x100000000 64bit pref] [ 8.991699] pci 0000:00:00.0: BAR 8: assigned [mem 0x30000000-0x300fffff] [ 8.998526] pci 0000:01:00.0: BAR 0: assigned [mem 0x30000000-0x30000fff 64bit] [ 9.005920] pci 0000:00:00.0: PCI bridge to [bus 01] [ 9.010933] pci 0000:00:00.0: bridge window [mem 0x30000000-0x300fffff] [ 9.017868] pci 0000:00:00.0: enabling device (0000 -> 0002) [ 9.023506] pci 0000:01:00.0: enabling device (0000 -> 0002) [ 9.029232] pci 0000:01:00.0: quirk_usb_early_handoff+0x0/0x9d4 took 11108 usecs [ 9.036879] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 9.042081] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1 [ 9.049910] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000040000000890 [ 9.059082] pcie_plda 2b000000.pcie: msi#0 address_hi 0x0 address_lo 0x190 [ 9.066397] xhci_hcd 0000:01:00.0: xHCI Host Controller [ 9.071593] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2 [ 9.079034] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed [ 9.086082] hub 1-0:1.0: USB hub found [ 9.089807] hub 1-0:1.0: 1 port detected [ 9.094874] hub 2-0:1.0: USB hub found [ 9.098597] hub 2-0:1.0: 4 ports detected [ 9.105653] pcie_plda 2c000000.pcie: host bridge /soc/pcie@2C000000 ranges: [ 9.112635] pcie_plda 2c000000.pcie: MEM 0x0038000000..0x003fffffff -> 0x0038000000 [ 9.120786] pcie_plda 2c000000.pcie: MEM 0x0980000000..0x09bfffffff -> 0x0980000000 [ 9.128947] ATR entry: 0x09c0000000 -> 0x0000000000 [0x0010000000] (param: 0x000001) [ 9.136727] ATR entry: 0x0038000000 -> 0x0038000000 [0x0008000000] (param: 0x000000) [ 9.144509] ATR entry: 0x0980000000 -> 0x0980000000 [0x0040000000] (param: 0x000000) [ 9.310323] usb usb2-port2: over-current condition [ 9.410297] usb 1-1: new high-speed USB device number 2 using xhci_hcd [ 9.470367] usb usb2-port4: over-current condition [ 9.570576] pcie_plda 2c000000.pcie: Port link down, exit. [ 9.590022] clk-starfive-jh7110-vout 295c0000.clock-controller: starfive JH7110 clk_vout init successfully. [ 9.593081] hub 1-1:1.0: USB hub found [ 9.607032] hub 1-1:1.0: 4 ports detected [ 9.611633] clk-starfive-jh7110-isp 19810000.clock-controller: starfive JH7110 clk_isp init successfully. [ 9.621848] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMA Controller, 4 channels [ 9.665290] printk: console [ttyS0] enabled0x10000000 (irq = 17, base_baud = 1500000) is a 16550A [ 9.665290] printk: console [ttyS0] enabled [ 9.673602] printk: bootconsole [sbi0] disabled [ 9.673602] printk: bootconsole [sbi0] disabled [ 9.683257] jh7110-vin 19800000.vin_sysctl: stfcamss probe enter! [ 9.691436] jh7110-vin 19800000.vin_sysctl: stfcamss probe success! [ 9.708872] dwmmc_starfive 16010000.sdio0: IDMAC supports 32-bit address mode. [ 9.709309] dwmmc_starfive 16020000.sdio1: IDMAC supports 32-bit address mode. [ 9.709574] jh7110-sec 16000000.crypto: will run requests pump with realtime priority [ 9.712804] jh7110-sec 16000000.crypto: Initialized [ 9.713907] starfive-i2s 120b0000.i2stx_4ch0: designware: play supported [ 9.713918] starfive-i2s 120b0000.i2stx_4ch0: designware: i2s master mode supported [ 9.714108] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe begin [ 9.714118] sf-mipi-dphy-tx 295e0000.mipi-dphy: ===> sf_dphy_probe enter, 445 [ 9.714248] sf-mipi-dphy-tx 295e0000.mipi-dphy: control ECO [ 9.714268] sf-mipi-dphy-tx 295e0000.mipi-dphy: supply mipi_1p8 not found, using dummy regulator [ 9.714565] sf-mipi-dphy-tx 295e0000.mipi-dphy: sf_dphy_probe end [ 9.714754] cdns-dsi 295d0000.mipi: dsi_sys_clk = 297000000 [ 9.714993] cdns-dsi 295d0000.mipi: starfive dsi bind end [ 9.716223] dwmmc_starfive 16010000.sdio0: Using internal DMA controller. [ 9.717317] of_cfs_init [ 9.717358] of_cfs_init: OK [ 9.717896] starfive-pwmdac 100b0000.pwmdac: clk_apb0 = 49500000, clk_pwmdac_apb = 49500000, clk_pwmdac_core = 406843 [ 9.718405] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 9.723510] dwmmc_starfive 16020000.sdio1: Using internal DMA controller. [ 9.731362] dwmmc_starfive 16010000.sdio0: Version ID is 290a [ 9.736267] dwmmc_starfive 16020000.sdio1: Version ID is 290a [ 9.743136] dwmmc_starfive 16010000.sdio0: DW MMC controller at irq 29,32 bit host data width,32 deep fifo [ 9.750789] dwmmc_starfive 16020000.sdio1: DW MMC controller at irq 30,32 bit host data width,32 deep fifo [ 9.757161] mmc_host mmc0: card is non-removable. [ 9.764377] mmc_host mmc1: card is polling. [ 9.829090] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 9.879524] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 9.888165] cfg80211: failed to load regulatory.db [ 9.980363] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 10.050391] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 400000Hz, actual 399193HZ div = 248) [ 10.278793] starfive soc:display-subsystem: bound 29400000.dc8200 (ops 0xffffffff81076fa0) [ 10.287279] innohdmi-starfive 29590000.hdmi: inno hdmi bind begin [ 10.296482] innohdmi-starfive 29590000.hdmi: [drm:inno_hdmi_bind] registered Inno HDMI I2C bus driver success [ 10.307240] innohdmi-starfive 29590000.hdmi: HDMI&AUDIO register done. [ 10.313972] innohdmi-starfive 29590000.hdmi: inno hdmi bind end [ 10.320000] starfive soc:display-subsystem: bound 29590000.hdmi (ops 0xffffffff81077d38) [ 10.328256] vs-simple-encoder soc:dsi-output: encoder_bind begin [ 10.334472] no panel, -517 [ 10.337259] vs-simple-encoder soc:dsi-output: encoder_bind error [ 10.343399] starfive soc:display-subsystem: bound soc:dsi-output (ops 0xffffffff81077980) [ 10.353137] [drm] Initialized starfive 1.0.0 20191101 for soc:display-subsystem on minor 1 [ 10.361886] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 10.369894] random: fast init done [ 10.373475] mmc_host mmc1: Bus speed (slot 0) = 198000000Hz (slot req 50000000Hz, actual 49500000HZ div = 2) [ 10.373510] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 10.390687] starfive soc:display-subsystem: [drm] Cannot find any crtc or sizes [ 10.390710] mmc1: new high speed SDXC card at address 59b4 [ 10.404408] mmcblk1: mmc1:59b4 ED2S5 119 GiB [ 10.416200] GPT:Primary header thinks Alt. header is not at the end of the disk. [ 10.423639] GPT:1638439 != 250347519 [ 10.427220] GPT:Alternate GPT header not at the end of the disk. [ 10.430300] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 300000Hz, actual 300000HZ div = 330) [ 10.433237] GPT:1638439 != 250347519 [ 10.433243] GPT: Use GNU Parted to correct GPT errors. [ 10.433269] mmcblk1: p1 p2 p3 p4 [ 10.880343] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 200000Hz, actual 200000HZ div = 495) [ 11.330341] mmc_host mmc0: Bus speed (slot 0) = 198000000Hz (slot req 100000Hz, actual 100000HZ div = 990) [ 12.410359] ALSA device list: [ 12.413381] #0: Starfive-PWMDAC-Sound-Card [ 12.417706] #1: Starfive-HDMI-Sound-Card [ 12.426320] Freeing unused kernel image (initmem) memory: 2196K [ 12.432545] Run /init as init process [ 12.436247] with arguments: [ 12.439240] /init [ 12.441563] earlyprintk [ 12.444389] with environment: [ 12.447560] HOME=/ [ 12.449944] TERM=linux find /dev/mmcblk1p4: 0 [ 12.801709] EXT4-fs (mmcblk1p4): recovery complete [ 12.814810] EXT4-fs (mmcblk1p4): mounted filesystem with ordered data mode. Opts: (null). Quota mode: disabled. mount: /rootfs/dev/shm: special device /dev/shm does not exist. mount: /rootfs/dev/pts: special device /dev/pts does not exist. INIT: version booting INIT: No inittab.d directory found [ 13.379302] EXT4-fs (mmcblk1p4): re-mounted. Opts: (null). Quota mode: disabled. INIT: Entering runlevel: 3 swapon: cannot find the device for PARTLABEL=hibernation Starting syslogd: OK Starting klogd: OK Running sysctl: OK Populating /dev using udev: [ 30.768729] udevd[231]: starting version 3.2.10 [ 30.782897] random: udevd: uninitialized urandom read (16 bytes read) [ 30.790581] random: udevd: uninitialized urandom read (16 bytes read) [ 30.797113] random: udevd: uninitialized urandom read (16 bytes read) [ 30.822431] udevd[232]: starting eudev-3.2.10 [ 30.938047] jpu: loading out-of-tree module taints kernel. [ 30.947064] cnm_jpu 13090000.jpu: init device. [ 30.947500] SUCCESS alloc_chrdev_region [ 30.955495] vdec 130a0000.vpu_dec: device init. [ 30.960060] SUCCESS alloc_chrdev_region done Initializing random number generator: OK Saving random seed: OK Starting rngd: OK Starting system message bus: dbus[280]: Unknown username "pulse" in message bus configuration file done Starting rpcbind: OK Starting iptables: OK Starting bluetoothd: OK Starting network: OK Starting Network Interface Plugging Daemon: eth0 [ 31.772194] starfive-eth-plat 16030000.ethernet eth0: PHY [stmmac-0:) [ 31.800496] starfive-eth-plat 16030000.ethernet eth0: Register MEM_TYPE_PAGE_POOL RxQ-0 eth1. Starting dropbear sshd: [ 32.139116] dwmac4: Master AXI performs fixed burst length [ 32.144659] starfive-eth-plat 16030000.ethernet eth0: No Safety Features support found [ 32.152611] starfive-eth-plat 16030000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 32.180295] starfive-eth-plat 16030000.ethernet eth0: configuring for phy/rgmii-id link mode [ 32.202369] starfive-eth-plat 16040000.ethernet eth1: PHY [stmmac-1:00] driver [YT8531 Gigabit Ethernet] (irq=POLL) [ 32.230385] starfive-eth-plat 16040000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 33.239567] starfive-eth-plat 16040000.ethernet: Failed to reset the dma [ 33.246281] starfive-eth-plat 16040000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed [ 33.255696] starfive-eth-plat 16040000.ethernet eth1: stmmac_open: Hw setup failed OK [ 33.291949] starfive-eth-plat 16040000.ethernet eth1: PHY [stmmac-1:00] driver [YT8531 Gigabit Ethernet] (irq=POLL) [ 33.310487] starfive-eth-plat 16040000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0 Starting NFS statd: OK Starting NFS services: OK Starting NFS daemon: rpc.nfsd: Unable to access /proc/fs/nfsd errno 2 (No such file or directory). Please try, as root, 'mount -t nfsd nfsd /proc/fs/nfsd' and then restart rpc.nfsd to correct the problem FAIL Starting NFS mountd: OK Starting isp_ctrl_daemon.sh: OK Starting DHCP server: [ 34.320275] starfive-eth-plat 16040000.ethernet: Failed to reset the dma [ 34.327002] starfive-eth-plat 16040000.ethernet eth1: stmmac_hw_setup: DMA engine initialization failed [ 34.336421] starfive-eth-plat 16040000.ethernet eth1: stmmac_open: Hw setup failed [ 34.371999] starfive-eth-plat 16040000.ethernet eth1: PHY [stmmac-1:00] driver [YT8531 Gigabit Ethernet] (irq=POLL) [ 34.390490] starfive-eth-plat 16040000.ethernet eth1: Register MEM_TYPE_PAGE_POOL RxQ-0 [ 34.919142] dwmac4: Master AXI performs fixed burst length [ 34.924653] starfive-eth-plat 16040000.ethernet eth1: No Safety Features support found [ 34.932600] starfive-eth-plat 16040000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 34.960643] starfive-eth-plat 16040000.ethernet eth1: configuring for phy/rgmii-id link mode FAIL Welcome to Buildroot buildroot login: